iPump6420 Terminal Commands

Available User Commands

? : Shows help for the last command you typed

abort : Abort Temporary insert

abortrec : to Tune to Commanded or Successful

To : S - Last Successful, C - Last Commanded

adds : location *settings [label]> Add Settings

Location : 1-48 (position in search table)
(*) Parameter does not apply to ASI input
*Carrier Freq.: Absolute value between carrier and LNB
LO freq. must be 950 MHz - 2150 MHz
*Data Rate : 2.5 - 100 Mbps
*FEC Rate : Depends on modulation type:
QPSK - 1/2,2/3,3/4,5/6,7/8
*Tag Site :
Program # : 1-65535, '*' selects wildcard
Label : 10 letter string (name of table entry)

afd r : Display AFD download status

ap : port descr - Set the audio descriptor for the given port number

port : Audio port number
descr : Audio Descriptor

ap2 : decno port descr - Set the audio descriptor for the given decoder and port number

decno : Decoder number
port : Audio port number
descr : Audio Descriptor

appstat : No Help.

apropos : Find commands pertaining to a certain word.

audatten : decno level - Set the attenuation level for the given decoder

decno : Decoder Number
level : Attenuation level in dB

audmute : decno [l(eft)] [r(ight)] - Mute the audio for decoder (optionally mute left or right)

decno : Decoder Number
left : Optionally mute just the left channel
right : Optionally mute the right channel

audroute : Set Audio Routing

Usage: AUDROUTE decno [portno] route
route: S = Stereo
1 = Left on Both
2 = Right on Both
R = Reverse Stereo

audunmute : decno [l(eft)] [r(ight)] - Unmute the audio for decoder (optionally unmute left or right)

decno : Decoder Number
left : Optionally unmute just the left channel
right : Optionally unmute the right channel

automation : [decoder] Start Automation Mode

Enables automation mode on the given decoder number.
[decoder]: Number of decoder to be enabled for automation mode

contentaccess : [ro|full] Sets the access level for content on the HDD

date : Print the current date and time

dec 1 audiosamplerate : Sets the output audio sample rate for the decoder

dec 2 audiosamplerate : Sets the output audio sample rate for the decoder

dec 3 audiosamplerate : Sets the output audio sample rate for the decoder

decabort : decno - Abort the temporary insert for the given decoder

decno : Decoder Number

decfollowtune : decoder - Change the given decoder to the legacy 'Follow Tune' mode

decno : Decoder number

dels : location Delete Settings

Location : 1-48 (position in search table)

errors : type threshold - Set alarm threshold

type: 'E' for Errored Seconds or 'C' for Continuity Errors
(C is not supported in this release)
threshold: Threshold when to decalre an alarm

gpi trap : [gpi_num enable] Get/SET trap on a state change for the given GPI number

With no parameters, this command reports a table of all available GPIs and
whether or not a change on that input will generate an SNMP trap. If
gpi_num is only given, you get the setting for that particular GPI
number. If the 'enable' parameter is given, you can set the state for the
given number.

Parameters:
gpi_num: GPI number from 0 to 6
enable: on or off

group add : group - Add the receiver to the given group

group del : group - Delete the receiver to the given group

h : Displays help

help : Displays help

hepl : Displays help

http proxy addr : proxy_ip_addr Sets/displays the HTTP Proxy Address

http proxy enabled : 0|1 Disables/Enables the use of the HTTP proxy info

http proxy port : proxy_port Sets/displays the HTTP proxy port

ifconfig : Displays the current ethernet device(s) configuration

ipconfig : Displays the current ethernet device(s) configuration

lan gateway : Sets the network gateway for the LAN interface

lan ip : Set the unit's static LAN IP Address

lan mode : Sets the LAN addressing mode. DHCP, STATIC

lan setup : [ip] [subnet] Sets up IP address and subnet mask for the LAN port

lan subnet : Sets the unit's static LAN Subnet Mask

listall : Displays the complete list of available commands with detailed help

lnbpwr : Turn LNB Power ON/OFF

lnbselect : Set LNB Mode UNIV/ASTRA or STD/LO

localtimezone : Set or display the local timezone.

To set: Parameter must be a path to an exisitng binary
zoneinfo timezone relative to the zoneinfo top-level directory.

log clear : [event type] Clear contents of the log

margin : margin_offset - Set SNR margin offset

Usage: MARGIN margin_offset

margin_offset Range: 1.0 - 10.5 dB

modem passwd : passwd Sets the PPP password

modem phone : number Sets the dialout phone number

modem prefix : string Sets the dialout phone number prefix

modem user : name Sets the PPP user name

movep : source destination Move Preset entry

source/destination: Preset Table entry number

movp : source destination Move Preset entry

source/destination: Preset Table entry number

net dhcpupdate : Tell devices in DHCP mode to poll for DHCP connection

net dns : [primary] [secondary] Sets the primary or secondary dns servers

oar record : Start record operation for a given tuner (See help for params)

port: Tuner port number (1, 2)
duration: Number of seconds to record
[prefix]: Prefix string to use for recorded file name

oar report : Status of Current Active Recording

oar tune : Set/get tuning parameters for tuner (See help for params)

[port]: Tuner port number (1, 2)
[frequency]: Frequency to tune to in kHz.
AM mode: 520 - 1720 kHz.
FM mode: 87000 - 108000 kHz.
WFM mode: 64000 - 108000 kHz.
SW mode: 153 - 28500 kHz.
[mode]: AM, FM, WFM or SW

perm : *settings [label] Set Perm Settings

(*) Parameter does not apply to ASI input
*Carrier Freq.: Absolute value between carrier and LNB
LO freq. must be 950 MHz - 2150 MHz
*Data Rate : 2.5 - 100 Mbps
*FEC Rate : Depends on modulation type:
QPSK - 1/2,2/3,3/4,5/6,7/8
*Tag Site :
Program # : 1-65535, '*' selects wildcard
Label : 10 letter string (name of table entry)

permch : location Set perm settings from settings table

Location : 1-48 (position in search table)

playfile : decno filename [trigger profile] - Play the filename to the given decoder using the optional parameters

decno: Decoder Number
filename: Filename to play
trigger: Set what trigger will cause the file to play
profile: Insertion profile to use to play the file

playlist delete : name - Delete the playlist with the given name

port : [number]> Select RBDS port

RBDS Command:
Select RBDS DB9 connector
sets DataRate {Databits,Parity,Stopbits}.

Usage:
PORT [number] [datarate] [settings]

number = 1 or 2 for the two RBDS DB9 connectors
datarate = 1200, 2400, 9600
settings = (7|8)(N|E|O|M|S)(0|1|2)

profile create : Creates a profile definition from the given arguments (See help)

number: Profile number to delete (1-255)
key: Valid keys include ducking, atten, interruptible, preSilence, and postSilence
value: For ducking and atten, 0-96 db in tenths of a dB
For silence keywords, 0-5000 ms
For interruptible, true or false

profile delete : Deletes a profile definition

number: Profile number to delete (1-255)

profile report : Reports all profile definitions

pw : passwd Sets the PPP password

r c : Report Carrier Status

r dec : No Help.

r g : [pagel] Report COMPEL Group Table (or page of it)

r groups : Report list of groups (not entire table)

r http : Report HTTP Information

r ns : Report Network Services Status

r oar : Status of Current Active Recording

r p : Report Configuration Information

r profile : Reports all profile definitions

r r : Report Relays Status

r rbds : Report RBDS Status

r s : Report Settings Status

r sched : Scheduler status

r st : Report Preset Table

r trigger : Trigger report

rbds baud : [port] [baud] Set/get RBDS port baud rate

port : RBDS port number. 1 or 2
baud : Baud rate 1200, 2400, 4800, or 9600

rbds report : Report RBDS Status

rd asi : Report ASI Diagnostics

rd ca : Conditional Access

rd rf : Report Carrier Acquisition/Tracking Diagnostics

re : state [number]> Turn Solid-state Relays On or Off

RElay Command:
Closes and opens the two available relays on the DB9 connector
and the relays on the relay-expansion card if installed.

Usage:
RE state [number]

number = 1 or 2 for the relays on the DB9 connector
or number = E1 - En for the relays on the expansion module
** if number is omitted then all are selected

state = ON or OFF.

reset : [-f] [-hw] [-sw] Resets/reboots via the requested options (defaults to -sw)

-f - Force a file system check after the reboot
-sw - Perform a 'software' reboot (this is the default)
-hw - Perofrm a 'hardware' reboot (reset line for PC-type systems)

rp ca : Conditional Access

rp rec : Report Auto Recovery status

rp rf : Report RF Parameters

rpath relay : addr, Sets the address of the ReturnPath or mail proxy server.

rpath send : [report_id] Sends the specified report to the ReturnPath server. See addtional help for id values

report_id: 0 - Health & Status Report (default)
1 - Asset Inventory Report
2 - As-run Log Report (with delete)
3 - As-run Log Report (no delete)
5 - Operational Log Report (with delete)
6 - Operational Log Report (no delete)
7 - Return ShowShift Show Definitions
8 - Return ShowShift Shift Definitions
10 - Return OAR files

rpath sendrpt : [report_id] Sends the specified report to the ReturnPath server. See addtional help for id values

report_id: 0 - Health & Status Report (default)
1 - Asset Inventory Report
2 - As-run Log Report (with delete)
3 - As-run Log Report (no delete)
5 - Operational Log Report (with delete)
6 - Operational Log Report (no delete)
7 - Return ShowShift Show Definitions
8 - Return ShowShift Shift Definitions
10 - Return OAR files

rpath srvraddr : addr, Sets the address of the ReturnPath or mail proxy server.

rpath srvraddrbackup : addr, Sets the backup address of the ReturnPath or mail proxy server.

savep : [entry#] [label] - Save current Settings to a Preset entry

entry# : A Preset Table Entry number or text "PERM"
label : Channel label

sched disable : Disable the local scheduler

sched enable : Enable the local scheduler

sched stat : Scheduler status

set : Set Individual Carrier Parameters

SET [parameter] [value]
SET TO [destination]
SET FROM [source]
parameter - one of format, feed, freq, rate, fec, tag, prog
value - value corresponding to the parameter as in any settings command

destination - PERM, TEMP, or a number of a table entry
to which the working settings should be stored.
source - PERM, CURR, CMD, or a number of a table entry
from which the working settings should be loaded.

setlnb : Set the LNB LO Frequency

LO_freq : 0 - 14000.00 MHz
LO_alias : C, KU, ELKU, EHKU

settimeout : source time Set Timeouts

source : 2-5 (timeout to set)
1 - Not Used (was Fade)
2 - Services Recovery (was Install)
3 - Network Recovery (was No Compel)
4 - Recovery Iteration (was Header Seek)
5 - Local (Control) Recovery
time : HH:MM:SS (length of time to wait)

snmp community : Set SNMPv2 Community Access String

snmp trap community : Set SNMPv2 Server Community Access String

With no parameters display community of the snmp server.
With parameters, set the server community.
Before being set, the community defaults to 'public'

snmp trap port : Set SNMPv2 Server port

With no parameters display the name of the snmp server.
With parameters, set the server address.
A server port of 0 means the default snmp server port.

snmp trap server : Set SNMPv2 Server Address

With no parameters display the name of the snmp server.
With parameters, set the server address.

snr : margin_offset - Set SNR margin offset

margin_offset: 1.0 - 10.5

sp : program Select default program for carrier

program : Program number from PAT or SDT descriptor

sp. : decno program - Set the program number for the given decoder number

decno : Decoder number
program : Program number

stat sched : Scheduler status

telnet : [remote ip addr] Use telnet client to connect to another host

temp : *settings time Set temp Settings

(*) Parameter does not apply to ASI input
*Carrier Freq.: Absolute value between carrier and LNB
LO freq. must be 950 MHz - 2150 MHz
*Data Rate : 2.5 - 100 Mbps
*FEC Rate : Depends on modulation type:
QPSK - 1/2,2/3,3/4,5/6,7/8
*Tag Site :
Program # : 1-65535, '*' selects wildcard
time : HH:MM:SS (length of time to tune)

tempch : location time Set temp settings from settings table

Location : 1-48 (position in search table)
time : HH:MM:SS (length of time to tune)

time server : IP address of NTP time server

time source : [compel | ntp] - Set time sync. source to compel or ntp

trigger availfire : [number] [avail] Fires given trigger number

trigger clear : [number] Clears the given trigger number

trigger eventfire : [number] Fires given trigger number

trigger fire : [number] Fires given trigger number

trigger report : Trigger report

ver : Show software versions

wan gateway : Sets the network gateway for the WAN interface

wan ip : Set the unit's static WAN IP Address

wan mode : Sets the WAN addressing mode. DHCP, STATIC, or WEG

wan setup : [ip] [subnet] Sets up IP address and subnet mask for the WAN port

wan subnet : Sets the unit's static WAN Subnet Mask

web home : [type] Set's the 'Home Page' that the user sees when visiting the unit's web site

type: standard or mobile

Diagnostic Commands

afd afdinit : Initialize afd

afd madd : AFD compel MADD cmd

afd mdel : AFD compel MREMOVE cmd

alarms : No Help.

appm appswitch : No Help.

appm checkapp : No Help.

appm dlok : No Help.

appm loadfile : No Help.

appm loadurl : No Help.

appm r : No Help.

appm resettestcnt : Resets the application test fail counters

appm setappflags : No Help.

appm setappgood : No Help.

appm stat : No Help.

asset autoconfirm : [1|0] Set/report asset auto-confirm setting

asset cleanup : dirName [xmlmd5sum] - Cleans up the given directory (relative to /u/user) using z_metadata.xml file

asset confirm : name [NAK_only=0] [verify=1] - Confirm a given asset/folder/file

assetmon checknow : Checks for new metadata.xml files on command

assocaud list : Lists all Associated Audio observers

audiobufferlevel : Set/show the default audio buffer level (milliseconds)

auth : No Help.

capid : [pid] Set/view the CA PID

carrierreq : [0|1] Sets/displays the requirement for a carrier. This controls alarm/warning indications

cert delete : Delete feature certificate

feature_name: Feature name to load

cert load : Load all feature certifcates from local Wegener server

cert loadfile : Load feature certificate from local file

feature_name: Feature name to load
file_name: File name to load certificate from

cert report : Report Certificate info

clrind : No Help.

cmddelay : Set/Query the network command delay sync. parameter

cmplint cmdpath : [path] Set/get the Compel over Internet command path

cmplint pollnow : Poll for Compel over internet commands NOW

cmplint polltime : [seconds] Set/get the Compel Over Internet poll time

cmplint srvraddr : [addr]. Set/get the Compel over internet server address. (Use NULL to disable)

cmplpid : No Help.

compel dpiavail : No Help.

compel dpievent : No Help.

compel errors : Show compel errors

compel header : No Help.

compel logclear : Clears the log of addressed Compel packets

compel logcnt : Displays how many addressed packets are in the Compel Log

compel logshow : [numToPrint] [printRaw] Print the log of addressed Compel packets

compel logsize : [size] Sets/Displays the maximum size for the Compel log

compel mirror : [sn] [clean] Have unit respond to compel commands of another unit. Use sn=0 to disable mirroring. WARNING: USING THIS COMMAND WITH 'clean' DELETES ALL CONTENT AND GROUP INFO

compel overip : No Help.

compel pid : No Help.

compel required : No Help.

compel test readfile : No Help.

compel timezone : read and/or set the compel timezone

compel trig : No Help.

compelrequired : No Help.

cond : No Help.

console : Console terminal mode

core alloc mark : Mark active memory allocations

core alloc show : [all=1,unmarked=2] [cmpfrndly] Show active memory allocations

core atom : No Help.

core build : No Help.

core config : No Help.

core exit! : Exit system

core hardtime : No Help.

core logpar : [ms] [grp] [ndx] [mem] Log PCMI parameter every N ms

core luaopts : No Help.

core mm : Display anyproc-mm

core productions : No Help.

core sems : Display semaphore usage information

core sysinfo : show system memory, etc. statistics

core systasks : Display all instantiated/active system tasks

core testblock : [cnt]

core uname : Display unit kernel version and HZ

core uptime : No Help.

core watchdog : report watchdog monitor status

dec 1 adecdbg : No Help.

dec 1 allowspliceravsync : No Help.

dec 1 decode : No Help.

dec 1 driver : No Help.

dec 1 dropb : No Help.

dec 1 gaba : No Help.

dec 1 nosend : No Help.

dec 1 repframe : No Help.

dec 1 seq : No Help.

dec 1 stat : No Help.

dec 1 vcxo : No Help.

dec 2 adecdbg : No Help.

dec 2 allowspliceravsync : No Help.

dec 2 decode : No Help.

dec 2 driver : No Help.

dec 2 dropb : No Help.

dec 2 gaba : No Help.

dec 2 nosend : No Help.

dec 2 repframe : No Help.

dec 2 seq : No Help.

dec 2 stat : No Help.

dec 2 vcxo : No Help.

dec 3 adecdbg : No Help.

dec 3 allowspliceravsync : No Help.

dec 3 decode : No Help.

dec 3 driver : No Help.

dec 3 dropb : No Help.

dec 3 gaba : No Help.

dec 3 nosend : No Help.

dec 3 repframe : No Help.

dec 3 seq : No Help.

dec 3 stat : No Help.

dec 3 vcxo : No Help.

decodelanip : Start decoding of IP stream

Command the specified decoder to begin playing an
IP/UDP Multicast or Unicast stream from the system
LAN port. If the IP multicast address is specified
as '-', IGMP join requests are not sent out (Unicast).

decoff : No Help.

decrejoin : No Help.

decsign : No Help.

descram dbg : Set/view Descram Debug level

descram debug : Set/view Descram Debug level

descram drop : Drop num seeds for testing

descram params : Show operating parametersl

dmx blockpid : Blocks a PID at the demux level (pid value in hex!)

dmx remappid : orig_pid remap_pid - Remaps orig_pid to remap_pid

dmx unblockpid : Unblocks a PID at the demux level (pid value in hex!)

dmxpktstats : [clear] Displays/Clears packet statistics from the demux

dpat : Display the current PAT information

dpi duration : No Help.

dpi send : [hex pid] [duration pts ticks]

dpsi : Display all current PSI information (PAT and PMTs)

dswegca drop : Drops the next seed received

dswegca start : Starts the Descram-WEGCA module

dswegca stop : Stops the Descram-WEGCA module

dvbipaddr : No Help.

dvbipport : No Help.

echo : echo commands

eeclear : offset(hex) len(dec) - Clears a section of ee memory

eemap : No Help.

eeread : No Help.

eewrite : No Help.

extrafiledelay : Add extra delay between STC and PTS when decoding files (increase buffering)

filercv controltimeout : Sets the AFD control timeout

filercv resendtimeout : Sets the AFD resend timeout

fsmgr chkexpired : Forces the system to check for expired files

getpidcnt : No Help.

gopher dump : show active/pending gopher processes

gopher mutex : No Help.

gopher once : Run lua script as gopher process

gopher repeat : [ms] [script] Run lua script on repeating timer every [ms] milliseconds

gpi r : Report status of General Purpose Inputs (GPI)

gpi test : No Help.

gpidelay : Set/Query the GPI execution delay parameter

hdd fail : Simulate a hard drive failure

hdd smart_thresh : Set EE smartctl warning threshold

hdd unfail : Attempt to 'unfail' a hard drive

httpdload attempts : Set/report the maximum number of attempts for HTTP download

httpdload file : url dest_file [size] [signature]- Send command to download a file via HTTP

httpdload maxrate : Set/report the maxiumum transfer rate (in Kbps) to use for HTTP file delivery

hwtest am : Verify AM Tuning

hwtest AM tuner_number freq_kHz [out_decoder]
tuner_number: 1 or 2
freq_kHz: AM or FM freq to test in kHz
[out_decoder]: Optional decoder number (1-3) to output to. Defaults to tuner_number

hwtest arly fail : Alarm Relay Hardware Test Fail

hwtest arly pass : Alarm Relay Hardware Test Pass

hwtest arly start : Execute Alarm Relays Hardware Test

hwtest audport : [1|2|3|pass|fail] Starts test on port #

or notes pass/fail status of last test

hwtest cleari2c : 6420 - command 0x40 to PIC: clear I2C

hwtest fm : Verify FM Tuning

hwtest FM tuner_number freq_kHz [out_decoder]
tuner_number: 1 or 2
freq_kHz: AM or FM freq to test in kHz
[out_decoder]: Optional decoder number (1-3) to output to. Defaults to tuner_number

hwtest fusb : [usb_device], Test the Front Panel USB Interface. Defaults to testing /dev/sdb1

hwtest hdd : Test the HDD using S.M.A.R.T. tools

hwtest irly fail : Expansion Relay Hardware Test Fail

hwtest irly pass : Expansion Relay Hardware Test Pass

hwtest irly start : Execute Expansion Relays Hardware Test

hwtest lan : ip_addr. Tests the LAN port using a PING to given ip_addr.

hwtest lcd fail : Stops the LCD test and indicates the test failed

hwtest lcd pass : Stops the LCD test and indicates the test passed

hwtest lcd start : Starts the front panel LCD hardware test

hwtest led fail : Stops the LED test and indicates the test failed

hwtest led pass : Stops the LED test and indicates the test passed

hwtest led start : Starts the front panel LED hardware test

hwtest linuxhw : Report Linux hardware information

hwtest lnb fail : Sets test Log to FAILED after test verification

hwtest lnb off : Set LNB Power OFF setting

hwtest lnb on : Set LNB Power ON setting

hwtest lnb pass : Sets test Log to PASSED after test verification

hwtest lnb toneoff : Set LNB for 22khz Tone OFF setting

hwtest lnb toneon : Set LNB for 22khz Tone ON setting

hwtest lnb v13 : Set LNB to output 13volts setting

hwtest lnb v14 : Set LNB to output 14volts setting

hwtest lnb v18 : Set LNB to output 18volts setting

hwtest lnb v19 : Set LNB to output 19volts setting

hwtest modem : Tests the built in modem

hwtest orly : Tests the opto inputs using the audio relays + spec. cbl

hwtest pushbtn fail : Stops the push button test and indicates the test failed

hwtest pushbtn pass : Stops the push button test and indicates the test passed

hwtest pushbtn start : Starts the front panel push button hardware test

hwtest rusb : [usb_device], Test the Rear Panel USB Interface. Defaults to testing /dev/sdb1

hwtest serial : Serial Port Hardware Test

hwtest smicro key : Test of the smicro_hpl send key function

hwtest smicro keytest : Test of the smicro_hpl decrypt key function

hwtest smicro report : Test of the smicro_hpl Report function

hwtest start : Starts Production H/W Testing

hwtest stop : Stops Production H/W Testing

hwtest temp : Tests the temperature sensor by reporting the current temp

hwtest urly fail : User Relay Hardware Test Fail

hwtest urly pass : User Relay Hardware Test Pass

hwtest urly start : Execute User Relays Hardware Test

hwtest ver : Report hw test version information

hwtest wan : ip_addr. Tests the WAN port using a PING to given ip_addr.

ind trapon : [state] Get/set trap on indication change state

stat: none|alarm|all

indpers : No Help.

indtable : No Help.

kencast off : Turn Kencast OFF

kmspars dbg : Enable/Disable WEGCA Parser Debug

kmspars debug : Enable/Disable WEGCA Parser Debug

kmspid : [pid] Set/view the CA PID

lan setfromcur : Sets the static LAN settings from the current setup

latchalarms : No Help.

lcd blink : No Help.

lcd cur : No Help.

lcd curpos : No Help.

lcd txt : No Help.

lcgi restart : Restarts the Lua CGI service

lnb report : Report of lnb_hpl variable settings

lnbloalias : [type] [freq] - Sets the LNB LO Alias Value

type: C, KU, ELKU or EHKU
freq: 0 - 14000 MHz

log add : [grp] [tt] [index] ( [mem] [val] ... ) add a test log entry

log count : Counts all unique events in the log

log dump : [numToPrint] Show contents of the log

log dump2 : Show contents of the log

log dumpasrun : [numToPrint] Show contents of the as-run log only

log dumpbin : Show binary dump of log as it will be returned to returnpath

log dumpop : [numToPrint] Show contents of operational events

log fill : n [asrun|op] Fill the log with 'n' test entries (defaults to op events)

log limits : Show/set limits on log sizes

usage: limits [whichlog] [maxevents]
Log Types are:
0:any/all logs; 1:As-Run log;2:Operational log; 3:Diagnostic log
Setting the limit on an individual log limits the # of events stored of that type.
Setting the limit on log 0 sets the max # of events (of all types together) to store.

log vacuum : Compact log database file

lua cmdargs : No Help.

lua test1 : No Help.

misc : No Help.

modemtimeout : No Help.

mpe pid add : Add an MPE PID (in Hex)

mpe pid r : Reports MPE PIDS

mpe pid remove : Removes an MPE PID (in Hex)

mute : No Help.

muteonreset : Mute all decoders on power up; 'E' for enable, 'D' for disable

net nvwipeout : Wipes out all ethernet device settings from the NV storage

netconlock : Set/Display the current local control level

netsrv abort : Aborts the current PPP connection attempt

netsrv checklan : No Help.

netsrv connecttime : No Help.

netsrv dialattempts : No Help.

netsrv dialinfo : No Help.

netsrv hasmodem : No Help.

netsrv lingertime : No Help.

netsrv secbetweenattempts : No Help.

netsrvs ftp : Turn ftp ON/OFF

netsrvs http : Turn http ON/OFF

netsrvs nfs : Turn nfs ON/OFF

netsrvs smb : Turn samba ON/OFF

netsrvs snmp : Turn snmp ON/OFF

netsrvs telnet : Turn telnet ON/OFF

nlog compat : Show legacy debug level ids

nlog d : [sink] [group] disable group

nlog drpn : [sink] [rpn...] disable group with rpn sets

nlog e : [sink] [group] enable group

nlog erpn : [sink] [rpn...] enable group with rpn sets

nlog filters : show all nlog filters

nlog show : sinkname group1 [group2] [group3] [...]

nlog sinks : show active nlog sinks

nlog test : enter an nlog test statement

nlog tgrp : [sink] [group] test nlog group active status

numpresets : Set/Get number of presets in the table

oar encparams : Set/get tuner's encoding parameters (See help for parameterrs)

[port]: Tuner port number (1, 2)
[bit_rate]: Bit rate of recorded material in Kbps.
Valid Values: 8, 16, 24, 32, 64 Kbps.
For 128 and 192 Kbps stable operation not guaranted.
[sample_rate]: Sample frequency in Hz.
Valid Values: 8000, 16000, 32000 Hz. Default: 32000 Hz
[stereo_mode]: S,s for Stereo and M,m for Mono. Default: Stereo
[bytes_per_sample]: 1 or 2. Default: 2

oar fileexpire : Set/get Number of days before recorded file will be deleted

[days]: Number of days (1-21)

oar send : Sent Recorded Files via Return Path

oar settime : set time of the day in seconds to delete oar files

oar siginfo : Send tuner signal information to logfile

command format: oar siginfo [port])
[port]: Tuner port number (1, 2)

oar volume : Get/set tuner input volume

[port]: Tuner port number (1, 2)
[volume]: Volume in dB from -60 to 20 dB

onlyaudiomode : No Help.

pcmi groups : display all pcmi groups

pcmi members : [group] display all members of a group

pcmi where : [group] show file where group handlers are defined

pic cleari2c : 6420 - command 0x40 to PIC: clear I2C

pic clrpins : pinsToClear Clear generic pins on PIC interface (in hex)

pic info : Get PIC information

pic resetrxhub : Reset i6420 RX Hub

pic send : cmd data Send command to PIC. Data is n bytes in hex

pic setpins : pinsToSet Set generic pins on PIC interface (in hex)

playlist play : No Help.

playlist print : Print the given playlist name

psi addw : No Help.

psi blockaud : [prognum] [auddesc] Blocks and audio descriptor for a program

psi blockprog : [prognum] Blocks a program in a PAT

psi dbg : No Help.

psi dpat : Display the current PAT information

psi dpsi : Display all current PSI information (PAT and PMTs)

psi forceupdate : test: force update of psi data to watchers

psi moveaud : [prognum] [auddesc] [newpid] Moves provided audio descriptor to new pid

psi rdb : No Help.

psi rmw : No Help.

psi stat : No Help.

r gpi : Report status of General Purpose Inputs (GPI)

r m : No Help.

r mpe : Report MPE PIDS

rbds test : port message Send test message to RBDS port

port : RBDS port number. 1 or 2
message : Test text string to send to RBDS port. Put in quotes if you want spaces

rsm : Report of smicro_hpl variable settings

sched dump : Dump the raw events in the local scheduler database

scr : 02CA|NONE. Sets/Displays the Descrambler Type to use

seq print : No Help.

seq validate : No Help.

setheader : No Help.

setlabel : Sets/Displays the unit label

setstore clear : No Help.

setstore ee : No Help.

showshift abortplay : shift_name Aborts current playback of shifted show

showshift abortrec : show_name Aborts currently recording show

showshift compressdelay : [delay] Set/get the MPEG compression delay (in ms)

showshift defineshift : json_str_def define and add new showshift shift operation from JSON string

showshift defineshow : json_str_def define and add new showshift show operation from JSON string

showshift losstartdelay : [delay] set or read initial silence (seconds) at start of LOS

delay : Number of seconds to delay the start of LOS when
the loss is > than LOS threshold (0 - 255)

showshift losthreshold : [threshold] set or read minimum silence duration to play LOS

threshold : Number of seconds a data loss event must be before LOS content is
used. 0 means to only insert silence. (0 - 3600)

showshift maxshowage : [age] set or read maximum age (days) for recorded show

age : Number of days to keep show episode files. 0 means to keep files
forever. (0 - 90)

showshift refreshdb : Refresh the ShowShift entries in the database

shuffler map : display current shuffler map

shuffler next : dir context - Get next shuffled for for given dir and context

shuffler reshuff : dir context - Test Re-shuffle time

shuffler time : Estimate time takes to reshuffle

sigloss : No Help.

signage off : Deactivate Signage display

signage rmseq : [seqname] Remove sequence from database

signage rotation : [0/90/180/270] Get/Set signage screen configuration.

signage setseq : [sign] [pane] [seq] Set the sequence for a pane

signage sign : Load a sign to display

smicro report : Report of smicro_hpl variable settings

srchman deadhw : No Help.

srchman reset : No Help.

srchman restart : No Help.

srchman start : No Help.

srchman stop : No Help.

srchman tunerignore : 1 = ignore, 0 = use tuner

stask_test dump : Dump static info

stask_test run : Run function tests

stask_test start : Start the test systask

stask_test stats : Print test systask stats

tempsens : Reports the system temperature

term baud : set terminal baud rate

term type : set terminal type (vt100,ansi,etc.)

test source espts : pid - Outputs the first 10 packets or runs for 5 seconds

test source pes : pid - Outputs the first 10 packets or runs for 5 seconds

test source ts : pid - Outputs the first 10 packets or runs for 5 seconds

test tcppio info : Displays setup info for the TCP PIO test module

test tcppio send : relayNumber - Sends a TCP PIO trigger to a pre-defined COMPEL IP address

threshold : mod_format fec_ratio Eb/No- Sets the Eb/No threshold value for a FEC/Modulation combo

trigger store lua : [num] [script] Stores given lua script as perm trigger num

tsrecord start : No Help.

tsrecord stop : No Help.

tz boundary : [boundary] interval (in seconds) at which tz playback can revert to live

boundary : Interval in seconds where tz playback may revert to live.
Boundary interval repeats starting at midnight. (0 - 28800)
Boundary period must divide a 24 hour span evenly.

tz delay : [dec] [secs]

tz threshold : [threshold] maximum allowable loss during a boundary time.

threshold : Maximum amount of time signal can be lost during one tz delay
boundary period before a reversion to the live stream is forced. (0 - 28800)

video hdmode : [decno] [mode]: Set HD video mode (480i/p, 576i/p, 720p, or 1080i/p)

wan haslink : No Help.

wan setfromcur : Sets the static WAN settings from the current setup